WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES dragspecialties.com All part numbers in BLUE are new for the OldBook. SECTION 10 656 See FATBOOK For Late Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. WIRE EXTENSION KIT FOR H-D HEATED GRIPS •PART #2120-0498 includes two 16ga wires along with simple-to-install nylon butt connectors •Cut and splice to desired length •Made in the U.S.A. FRONT TURN SIGNAL EXTENSION HARNESS KITS •A must when installing taller handlebars •Intended for front turn signals mounted on handlebar switch housings on most 96-99 models •No crimping necessary •Made in the U.S.A. UNIVERSAL HANDLEBAR SWITCH WIRE EXTENSION KITS •Designed for those who would rather stagger-cut and solder in order to lengthen their wiring for taller bars •Wires are pre-stripped with the slug left in place to prevent fraying and the other end has machine-crimped terminals that can easily be reinstalled into the factory connector •All kits come 100% complete with OEM color matching wire and all the heat-shrink tuning needed to do the job right •24” L universal handlebar switch wire extensions; fit up to 20” Apes •Made in the U.S.A READY-TO-INSTALL HANDLEBAR WIRE EXTENSION HARNESSES •All the items needed to successfully extend the wiring to a set of OEM H-D handlebar switches •Harnesses include both male and female Molex terminals crimped on each end •Kits for all except FLHT and FLT models include wire heat shrink, a length of 3/8” heat shrink and color-matching wire •Kits for FLHT and FLT models include wire heat shrink, a length of 1/2” heat shrink and color-matching wire •Made in the U.S.A. HANDLEBAR SWITCH WIRE EXTENSIONS •24” L and 48” L wire extensions •For cut and solder applications •Wire ends are stripped but left with slugs to prevent fraying •Made in the U.S.A. HARNESS TURN SIGNAL TAP •Front turn signal tap •For adding additional front turn signals •Direct plug-in installation, no cutting or splicing •Made in the U.S.A. PART # DESCRIPTION 2120-0498 For all 96-99 Evolution Big Twin PART # DESCRIPTION FOR 96-99 SOFTAIL, 96-98 DYNA 2120-0344 +4” 2120-0345 +8” 2120-0346 +12” 2120-0347 +15” PART # DESCRIPTION 2120-0497 For 96-98 FLT/FLHT PART # DESCRIPTION 2120-0496 For 96-99 Evolution Big Twin (except FLT/FLHT) PART # DESCRIPTION FOR 96-98 FLHT/FLT (24 WIRE) 2120-0225 +4” 2120-0226 +8” 2120-0227 +12” 2120-0228 +15” PART # DESCRIPTION FOR 96-99 EVOLUTION BIG TWIN (EXCEPT FLHT/FLT) (12 WIRE) 2120-0233 +4” 2120-0234 +8” 2120-0235 +12” 2120-0236 +15” PART # DESCRIPTION FOR 82-95 MODELS (EXCEPT DRESSERS) 2120-1020 24” L extension 2120-1021 48” L extension PART # DESCRIPTION 2120-1116 For 96-98 FLHR/FLHT 2120-0344 2120-1021 2120-0496 2120-0497 2120-0225
RkJQdWJsaXNoZXIy OTcxOTk3