WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES dragspecialties.com All part numbers in BLUE are new for the OldBook. SECTION 10 624 See FATBOOK For Late Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. 12V REGULATOR •Internal wire connections are vibration-resistant •Fiber and Mylar® insulating pads •Large-diameter contact surfaces •Made in the U.S.A. 12V REGULATOR •Vibration-resistant internal wire connections; fiber and Mylar® insulating pads and large-diameter contact surfaces •Made in the U.S.A. GENERATOR-MOUNTED REGULATORS •Available for 12V applications in a black finish •Updated end plate has an extra set of mounting holes to align the fins on the regulator with the fins on the engine •If you have purchased a Cycle Electric generator since 1984, it may have the four-hole end plate •Updated end plate is available separately if your current generator is not equipped with one (comes complete with bearing and seal) CHROME REGULATOR COVER •Stamped steel cover fits over the existing regulator •Includes chrome mounting hardware CHROME REGULATOR MOUNT FOR RUBBER-MOUNTED MOTORS •Chrome regulator mount made of heavy-duty steel •Dual holes for custom applications CUSTOM REGULATOR MOUNTS •Allow the regulator to be mounted down and back out of sight •Require two 1/4”-20 x 1/2” bolts for installing regulator mount and two 3/8”-16 x 2 3/4” bolts for installing mount to the frame REGULATOR BRACKET •No drilling is required to mount this heavy-gauge, chrome-plated steel regulator bracket •Exact replacement for the stock regulator mounting bracket NOTE: When converting regulators on 70-75 models to a Dragtronic™ or Accel regulator, use Drag Specialties bracket, PART #DS-330023. VOLTAGE REGULATOR MOUNTING KIT •Kit includes three rubber insulators with nuts and lock washers •Made in the U.S.A. PART # DESCRIPTION 2112-0560 For 65-69 FL/FLH, 67-78 XLH; repl. OEM #74510-64 PART # DESCRIPTION DS-325496 For 65-69 FL/FLH, 67-78 XLH; repl. OEM #74510-64 PART # DESCRIPTION DS-325483 For all Shovelhead/Panhead/XL 12V standard generators w/ updated end plate (4-hole) DS-325484 For all Knucklehead/Panhead/XL 6V generators w/ updated end plate (4-hole) DS-313070 For all Shovelhead/Panhead/XL 12V low output generators w/ updated end plate (4-hole) PART # DESCRIPTION 7805-0012 For 89-99 FXST/FLST; repl. OEM #74578-97 PART # DESCRIPTION DS-330006 For 84-95 FLT and 84-94, 99 FXR; repl. OEM #74529-79T PART # DESCRIPTION FOR 36-99 BIG TWIN DS-720018 Chrome PART # DESCRIPTION FOR 36-99 BIG TWIN (CONT) 2112-0927 Gloss black PART # DESCRIPTION DS-330023 For 76-85 FX and FL; 80-86 FXWG; repl. OEM #74533-75B PART # DESCRIPTION 2401-0607 For 65-69 Big Twin and 67-77 XL •12V regulators are available in a standard or low output style (for use with small batteries in wraparound oil tanks) •Made in the U.S.A. •Optional 10-24 holes on back of mount for ground wire •Made in the U.S.A. NOTE: May require removal of the oil filter for installation. DS-325483 DS-313070 DS-720018 2112-0927
RkJQdWJsaXNoZXIy OTcxOTk3