WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES dragspecialties.com All part numbers in BLUE are new for the OldBook. SECTION 6 360 See FATBOOK For Late Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION CYLINDER LENGTH FOR 80”/89”/96” S&S BIG TWIN EVOLUTION STYLE MOTORS AND HEAD KITS 1050-02921 Fits stock CV carburetor on S&S 3.625”, 4” and 4.125” bore motors 4.9365” 1050-02952 Fits stock CV carburetor on S&S 3.625”, 4” and 4.125” bore motors 4.9365” 1050-02942 Fits stock CV carburetor on S&S 3.625”, 4” and 4.125” bore motors 5.550” 1 Requires the use of S&S manifold O-rings and U-rings (sold separately). Will fit S&S Hot Setup and Super Stock™ head kits. 2 Requires the use of S&S manifold O-rings and U-rings (sold separately). SPIGOT-MOUNT INTAKE MANIFOLDS FOR S&S HEADS •Used to install a stock CV carburetor on S&S 3.625”, 4” and 4.125” bore motors •Will also fit S&S Hot Setup and Super Stock™ head kits •PART # 1050-0295 is used to install 48 mm CV or Mikuni carburetors •Made in the U.S.A. NOTE: Not for use with OEM-style O-rings, requires the use of S&S manifold O-rings and U-rings, sold separately. 1050-0295 PART # DESCRIPTION FOR 84-99 EVOLUTION BIG TWIN 1050-0291 For S&S E series carbs PART # DESCRIPTION FOR 84-99 EVOLUTION BIG TWIN (CONT) 1050-0046 For S&S G series carbs FLANGE MOUNT INTAKE MANIFOLDS •For mounting an S&S E and G series carburetor or flange mount carburetor on models that require a manifold with a map sensor port •Comes with a map sensor port and match OEM intake ports •Made in the U.S.A. PART # DESCRIPTION FOR 84-99 EVOLUTION-STYLE BIG TWIN 1050-0293 For Super E carbs (no MAP sensor port) PART # DESCRIPTION FOR 84-99 EVOLUTION-STYLE BIG TWIN (CONT) 1050-0110 For Super G carbs (no MAP sensor port) FLANGE MOUNT INTAKE MANIFOLDS •Can be used to replace stock “compliance fitting” manifold on 84-89 and stock rigid-mount manifold from 90-99 •Use with stock or S&S cylinder heads •For use with stock 5.550” length cylinders •Requires the use of S&S intake seals and flanges (sold separately) •Made in the U.S.A. 1050-0046 PART # DESCRIPTION 1050-0296 Manifold conversion kit MANIFOLD CONVERSION KIT FOR 80” EVOLUTION •Kit converts stock 80” Evolution manifold to a more rigid-mount system •Eliminates cracking and leaking problems associated with the stock rubber compliance fittings •Includes an S&S Performance manifold, mounting flanges, two specially molded O-rings and two 0.350” spacers for spacing out the stock air cleaner or carb mount bracket •Fits 84-99 80” models if flange-type carburetor or adapter is used •Replacement flange seals also available •Made in the U.S.A. NOTE: Not for use with an S&S G series carb. PART # DESCRIPTION FOR 66-E78 SHOVELHEAD AND 57-78 XL (O-RING TYPE) DS-289231 Super B and E 1050-0047 Super G PART # DESCRIPTION FOR L78-84 SHOVELHEAD (W/O VOES) (BAND TYPE) DS-289232 Super B and E 1050-0050 Super G STANDARD INTAKE MANIFOLDS •Available for stock length cylinders •Compatible with S&S Super E, B and G carbs •L78-84 Shovelheads use rubber-band-type intake seals •66-E78 Shovelheads use O-ring-type intake seals •Made in the U.S.A. 1050-0047
RkJQdWJsaXNoZXIy OTcxOTk3