WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES dragspecialties.com SECTION 5 All part numbers in BLUE are new for the OldBook. 331 See FATBOOK For Late Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. PART # DESCRIPTION 1860-0667 Repl. 1” W OEM muffler clamps; fit mufflers with 1.75” ID inlets ; repl. OEM #65296-95A 1860-1382 For 95-98 FLT/FLHT/FLHR/FLTR models w/ 2.00” inlet mufflers (set includes two 2.00” reaction block stainless steel clamps) STAINLESS STEEL MUFFLER CLAMPS •Feature a 1.25” wide stainless band with an exclusive reaction block for 360° clamping without muffler or header distortion •High-strength fastener hardware with corrosion-resistant coating included •Replace 1” W OEM muffler clamps; fit mufflers with 1.75” ID inlets •Sold in pairs •Made in the U.S.A. PART # DESCRIPTION 1861-0679 1.44” to 1.58” 1861-0680 1.56” to 1.70” 1861-0681 1.69” to 1.87” 1861-0683 1.94” to 2.12” 1861-0684 2.06” to 2.24” PART # DESCRIPTION 1861-0685 2.19” to 2.37” 1861-0686 2.31” to 2.49” 1861-0687 2.44” to 2.62” 1861-0688 2.63” to 2.81” STAINLESS STEEL EXHAUST CLAMPS •Barrel and band design provide for superior clamping pressure •Low-profile hex-head adjusting bolt •Holds up to the repeated heating and cooling of the exhaust system •Sold individually •Made in the U.S.A. PART # DESCRIPTION 1860-0234 For L85-98 FLT/FLHT/FLHR/FLTR PIPE HANGER •Used to mount 1 7/8” diameter pipe extensions that have no brackets •Chrome finish •Sold each •Made in the U.S.A. PART # DESCRIPTION DS-203206 3” P-clamp PART # DESCRIPTION DS-203207 3” P-clamp w/ 2.5” tail P-CLAMPS •P-clamp mounts Paughco muffler PART #DS-202209 and most other 3” mufflers •Include nuts and bolt •Sold each •Made in the U.S.A. FOR 84-99 EVOLUTION BIG TWIN PART # DESCRIPTION STANDARD KITS; REPL. OEM #S 65328-83/8 3A, 65325-83/83A DS-203097 Chrome 1861-0889 Polished stainless steel HEAVY-DUTY KIT; REPL. OEM #S 65184-02, 65325-83/83A 1861-0888 Polished stainless steel REPLACEMENT RETAINING RINGS 1861-0458 Retainer ring clips (pr.) (Genuine James); repl. OEM #65325-83 DS-203109 Retainer ring clips (10 pk.); repl. OEM #65325-83 EXHAUST FLANGE KITS •Kit includes two flanges and two retaining rings •Heavy-duty kit has thicker flanges for less distortion •Replacement retaining rings can be purchased separately PART # DESCRIPTION 0930-0136 For all 84-99 Evolution Big Twin; repl. OEM #16715-83 EXHAUST STUD •5/16”-18, 5/16”-24 x 1.910” •Zinc-plated, steel •Sold each •Made in the U.S.A. PART # DESCRIPTION 2401-0126 For 84-99 Evolution Big Twin; repl. OEM #16715-83 EXHAUST PORT STUDS AND NUTS •Kit includes four zinc-plated studs and four chrome-plated flanged nuts; replaces OEM #16715-83 •Made in the U.S.A. PART # DESCRIPTION DS-197019 For all 84-99 Evolution Big Twin; repl. OEM #16715-83 EXHAUST STUDS •Sold in pack of six •Coarse thread (#18) to fine thread (#24) •Made in the U.S.A. 1861-0679 1860-0667 1860-1382 DS-203206 DS-203207 DS-203109 1861-0888 DS-203097
RkJQdWJsaXNoZXIy OTcxOTk3