dragspecialties.com SECTION 6 All part numbers in BLUE are new for 2026. WINDSHIELDS & FAIRINGS AUDIO, COMMUNICATION & MOUNTS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION & DRIVELINE ENGINE GASKETS & SEALS LIGHTING ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES DASHES & GAUGES FENDERS & LICENSE PLATE FRAMES HARDWARE, COVERS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES 651 See OLDBOOK For Early Model Applications DISCLAIMER: *EMIS (EMISSIONS CATEGORIZATION CODE). SEE PAGES 5-7 FOR CATEGORY CODES, IMPORTANT EPA/CARB EMISSION DEFINITIONS AND REGULATORY COMPLIANCE AND NOTICE REGARDING NOISE REGULATIONS. PRODUCTS NOT LEGAL FOR SALE OR USE IN CALIFORNIA ON ANY POLLUTION CONTROLLED MOTOR VEHICLES IF NOT CATEGORIZED AS “1” OR “4”. AUTOTUNE KITS FOR POWER COMMANDER V •Plugs directly into the Power Commander V with a single cable •Includes 18 mm O2 sensors and power connector that plugs into the bike’s harness •Makes automatic fuel adjustments •User can specify what air/fuel ratio to make each rpm and throttle position percentage combination •Makes it possible to adjust cruise for best fuel economy as well as larger throttle openings for peak power •Base settings included for air/fuel ratios, but are fully adjustable if need be •Requires installation of two 18 mm sensor bungs included •Made in the U.S.A. NOTE: Because of possible clearance issues, some aftermarket exhaust systems may require modifications or relocation of their sensor bungs. 1020-1117 PART # DESCRIPTION EMIS* 1020-2371 POD-300 digital display N/A POD-300 DIGITAL DISPLAY •Real-time fuel adjustment •Display channels real-time: rpm, TP, map position (when using map switch), duty cycle, fuel exchange, ignition change and wideband air/fuel ratio (with WB2 or AutoTune connected) •Weather resistant for use in all conditions •Log channels saved to internal memory and can be viewed/ analyzed with Dynojet’s powercore software •High-contrast display, viewable in sunlight •Includes CAN cable for attachment to Power Commander V, AutoTune and Wide Band Power Commander •Made in the U.S.A. NOTE: Not for use with Power Commander III USB. PART # DESCRIPTION EMIS* WITH O2 SENSORS 1020-4037 For 21-24 M-Eight w/ software level 28 2 1020-2491 For 14-20 Dresser 2 1020-2485 For 10-13 Dresser 2 1020-2483 For 07-09 Dresser, 07-11 FXST/FLST (except 07-11 CVO models), 06-11 Dyna, 08-11 V-Rod, and 07-13 XL 2 1020-2489 For 12-17 FXST/FLST and 12-17 Dyna 2 1020-2495 For 14-22 XL (except RH Sportster) 2 1020-2487 For 12-17 V-Rod 2 PART # DESCRIPTION EMIS* WITHOUT O2 SENSORS 1020-4046 For 21-24 M-Eight w/ software level 28 2 1020-2492 For 14-20 Dresser 2 1020-2486 For 10-13 Dresser 2 1020-2484 For 07-09 Dresser, 07-11 FXST/FLST (except 07-11 CVO models), 06-11 Dyna, 08-11 V-Rod, and 07-13 XL 2 1020-2490 For 12-17 FXST/FLST and 12-17 Dyna 2 1020-2496 For 14-22 XL (except RH Sportster) 2 TARGET TUNE •Allows the factory ECM to interpret and use wideband O2 sensor signals •Target fuel table from the calibration is achieved in real time •Retains OEM closed loop and achieves adaptive fuel control strategy •Learns and uses VE table corrections as you ride •Does not interfere with dealer diagnostic/service tools •Includes OEM style connectors to plug into factory O2 harness, either 2- or 4-pin versions •Available with or without O2 sensor •Made in the U.S.A. NOTE: Because of possible clearance issues, some aftermarket exhaust systems may require modifications or relocation of their sensor bungs. PART # DESCRIPTION EMIS* 1020-1559 For 14-20 Dresser, 12-17 FXS/FLS/FLST, Dyna and 12-17 XL w/ CAN Bus 6-pin connector 3 PART # DESCRIPTION EMIS* 1020-1117 For 10-13 Dresser w/ 12 mm O2 sensor (except FXST/FLST, Dyna 4-pin connector models) 3 1020-2490 1020-2483
RkJQdWJsaXNoZXIy OTcxOTk3